Search results

looking for a repair manual for my 2017 Sidewinder ltx se

Does anyone know who to contact about a wiring diagram for my 2011 apex se?

Good day everyone, Does anyone know if the Mag/rotor on a 2011 apex is the same as a 2006-2010 apex? I know the stator was updated in 2011 model change for higher output because of eps and exup but did the mag/rotor also change?

Hey guys, I’ve been chasing a hot soak starting and stalling problem on my 2011 apex 290hp rear mount mcxpress kit. Battery brand new, hooked up fuel pressure gauge, pressure at 44-46 psi consistently, replace cts to eliminate that. Idle air control motor, new. I have even disconnected pcv and...

Does anyone know how it. Works and what is lambda smoothing on the pc-5?

Hello, Does anyone know fuel pressure setting for 290hp Mc xpress on a 2011 apex?

Looking for a tune file for my 2011 apex and 290hp MCX kit

Went out today and sled ran fine for 2 two hours. i was boosting and running about 10500 rpm and sled shut down just like I shut it down. cde 43 came on dash. any ideas?

Hello Everyone. Just in the middle of a 290hp mc xpress install on a 2011 apex se and the pressure tube install. Looks like you have to remove the riveted hardware on the tunnel, for the tunnel protectors, in order to install the p-tube. Is that correct? The instructions don't really explain...

Has anyone tried running a 26t top gear and 38t bottom gear? Will a 290hp apex turbo have enough to pull this gear set-up?

My 06 apex gt mcx 260hp kit doesn't start when cold and sometimes after hot soak. It has a brand new fuel pump relay, upgraded fuel pump(external walhbro), new plugs. When cold ,it will fire, and sometimes try to idle for 1 or 2 seconds and then stall. It will take about 10 minutes of multiple...

I have an 06 apex gt. After install of 260 hp mcx kit, I can only see max. 7psi on boost guage. As far as I know, this kit is pre-set at 12-13psi. This is the second generation kit that controls boost with an electrical solenoid valve on vacuum line on turbo waste gate. I have checked both...

Does anyone know how to increase boost on new mcx rear mount that has wastegate control by c.d.i box and solenoid.

I have an 06 apex gt. I had to repair the sub lead to it underneath, due to ice build up damage. After the repair, the shock is adjusting now on the display when commanded, but I cannot feel or hear anything from shock when adjusting it with key on but not running. Is this normal?

Just finished installing a new mcx rear mount on an 06 apex gt and upon first start up, it idles fast enough to slightly engage clutch and when it warms up, it will stall and try and hunt for a steady idle. Only changes were head shim and intake cam sprocket mod. It seems like cam timing may...

Traded my 03 rx1 for 06 apex gt in order to upgrade to e.f.i and improve weight transfer with new mono rear skid. I am happy with sled except no matter what I do with transfer rod or shock adjustments, it does not hook out of the hole very well and feels just like my old rx1. It has stock...

Traded my 03 rx1 for 06 apex gt in order to upgrade to e.f.i and improve weight transfer with new mono rear skid. I am happy with sled except no matter what I do with transfer rod or shock adjustments, it does not hook out of the hole very well and feels just like my old rx1. It has stock...

Hey guys, I know this topic has been beat to death, but I can't seem to find any info in the search forum. Where do you install these 5/16 lock washers in the secondary for full shift out.

Has any one ever tried to pull start one of these four strokes by wrapping the primary with a strap. I know it would have some serious opposition when pulling, but in an emergency, it is nice to know in a pinch.

Is it possible to change Hyfax on an 06 apex gt without rear skid removal.