Search results

Is that just a complicated way of saying they include a spring shim ($0.50) and 3 rivets ($1.00 ea.) for $89.99 ? Or did I miss something ? Looking for a clutch kit, anyone have suggestions ? I'm hitting the rev limiter all the time it seems.

What does Yam do for this recall ? I've red loctited everything, it's fine for 200 miles, then everything gets loose again, causing a VERY dangerous situation, specially with the new C&A skis, they bite hard at times... Do they use new nyloc nuts or something? I am not taking it to my...

Hi All, Just wanted to get into index racing the Phazer on asphalt. I figure it should be consistent, having only 80HP and EFI, and well, a built in radiator... I have already purchased a track 128"X10.? I have a rail ext. and 8" wheels our back. How many more wheels should I add to...

Do the wheels end up inside or outside the rails ?? I am talking about part # SMA-8FA95-00-00 I need more wheels, but I need them on the inside of the rails only. (13.5" wide track) Thanks.

Anyone know if you can get gears from the aftermarket instead of paying the Yamaha price? I'd like either a 17T top or a 42T bottom gear. Royal distributing doesn't list gears for the 2007 YPZ.... Looking for a bit extra bottom end grunt to help turn the longer paddle track.

Hi, Just wondering if anyone here knew anything about what needs to be done when wedling onto the '07 Phazer... I have a small repair to make in the front frame, it's a pretty accesible spot, and I don't need to remove the whole thing to weld it. What electronic components should I...

I've been getting some PM's about how the install went. Parts: MMP Rail Extensions (bought from Dennis Kirk) 3.75" -136" to 144" OFFSET for 8" Big Wheel swap. (2) Cat M8 8" rear wheels (These are priced WELL and have a removable bearing, same size as stock Phazer) (1) 128" X 13.5"...

Yes, you read that correctly, $2243.02 LOL. Was just riding around, hitting drifts, ect. Not HUGE air, but a few feet I guess. I was riding with a 99 MXZ670, and an older Polaris, was doing the same as what they were doing... Nothing my old '93 Exciter SX couldn't handle. Noticed the...

I just picked one up, waiting on delivery, brand new take off. The plan, 3 main issues : 1. Get the 4th rear wheel kit from Yamaha, and completly delete the 2 outer wheels in my skid. (Like the Cats) -- Wondering if this is "safe" to do WITHOUT having to worry about snagging the...

I used some 14$ ATV handle bars. I had to make them a tad wider (to fit the thumb throttle, handguards, and kill sw. block), using one of the 5 sets of bent bars I have in my shop, I cut two 1.5" pieces, and welded them to each side of my new bars. It ended up being about a 2-2.5" rise, and...

Has anyone else got this? Mine's filling up with water... This had happened before I installed my exhaust, or blocked the tunnel hole, so you can't blame that. Should Yam cover this under warranty? I was about to take it apart, and re-silicone it, but maybe I should let Yamaha do it...

I'd just like to confirm that the sled DID not lose any RPM on top end, I put about 30 35 miles on it today, and it basically runs just like stock, but sounds better. I was testing with 4 disks which is the mininum recommended amount. I saw anywhere from 11300 to about 12000 RPM, and did not...

8 MPG and it hit 98 on the dreameter today on the lake, about 1/2" of slush over ice. just above freezing temps. Buddy beside me clocked me at 86-87 on an FIII Should I look for a fuel leak? I was driving the thing like a light switch though...

Anyone make something to fit the non-shielded sleds, complete with mounting braket, and all that junk? Looking for something low, maybe a tad lower than the FX shield, in black of course. I don't even want to get a price from Yamaha cause I know it will be crazy. :Rockon:

Is the Phazer engine 449cm3 or 499cm3...? My Yamaha owners manual says 449cm3, and the sales brochure indicates 499.