BOONDOCKERDB
Newbie
- Joined
- Oct 29, 2010
- Messages
- 1
2000 MILES SO FAR NO PROBLEMS YET..
canoehead
TY 4 Stroke God
- Joined
- Jan 14, 2011
- Messages
- 2,136
- Location
- NE, Alberta
- Country
- Canada
- Snowmobile
- 2014 XF9000, 2016 Viper XTX
Just went over 2000 kms. I bought it new in November 2010!
Nothing up!
Nothing up!
yukon yamaha
TY 4 Stroke Master
- Joined
- Jan 30, 2008
- Messages
- 1,092
- Age
- 39
- Location
- WHITEHORSE, YUKON CANADA
- Country
- Canada
- Snowmobile
- 2008 nytro custom! 2014 viper custom
4500 kms boosted 15 psi no problems
kamakazie
Veteran
5000 Miles so far one Engine rebuild covered by YES. Sled was on it's left hand side and oil leaked into the engine. Not good. Can you say check valve!!! Come on Yamaha! Other than that it has been a great sled!!!
mike3577
Expert
- Joined
- Oct 18, 2009
- Messages
- 309
- Location
- auburn hills,mi
- Country
- USA
- Snowmobile
- 09 nytro xtx, 8 inch slydog powederhounds, mbrp silencer, ulmer racing clutching, fast track studs,cr10ek sparkplugs,
2500 miles two belts
canuk77
Extreme
I got 5000 miles with no problems...
rrxx-1
Expert
4000 miles on mine, one subframe, balljoints, one belt
5000 miles on my brothers, balljoints, one belt
Both sleds are going to get tore down this summer, new balljoints, bushings, and bearings.
5000 miles on my brothers, balljoints, one belt
Both sleds are going to get tore down this summer, new balljoints, bushings, and bearings.
Old Thumper
Pro
7104
I guess I win. (so far)
I guess I win. (so far)
arteeex
TY 4 Stroke Master
8027, but it was a low mile season.
grizztracks
Tech Advisor
- Joined
- Feb 24, 2005
- Messages
- 3,110
- Age
- 60
- Location
- Scio, NY
- Country
- USA
- Snowmobile
- FX Nytro RTX, RS Vector, SR Viper RTX SE
5000 miles on mine and engine runs great.
So far:
Lower ball joints replaced under warranty (1500 miles)
Bent 08 subframe replaced with 09 frame under warranty (1500 miles)
Tunnel heat exchanger added to the inadequate stock cooling system
Exhaust donuts (3000miles)
1 hyfax replacement (3500 miles)
A-arm bushings replaced with Ulmer's (3500 miles)
Bent 09 subframe replaced with updated 2010 frame (reinforcement gussets added)
Before next season:
Upper and lower ball joints
Outer tie rod ends
Spark plugs
Belt
So far:
Lower ball joints replaced under warranty (1500 miles)
Bent 08 subframe replaced with 09 frame under warranty (1500 miles)
Tunnel heat exchanger added to the inadequate stock cooling system
Exhaust donuts (3000miles)
1 hyfax replacement (3500 miles)
A-arm bushings replaced with Ulmer's (3500 miles)
Bent 09 subframe replaced with updated 2010 frame (reinforcement gussets added)
Before next season:
Upper and lower ball joints
Outer tie rod ends
Spark plugs
Belt
Old Thumper
Pro
Old Thumper said:7104
I guess I win. (so far)
I knew there must be higher miles out there...
Replaced lower ball joints
Made bronze A arm bushings
Did the upper ball jt mod
Added Yamaha wet left foot fix
Replaced sliders twice
Replaced carbides twice (Bergstrom Triple pts)
Changed exhaust doughnuts
Replaced belt after 5200 mi
Added a temp gauge
Added a manual fan bypass switch
Added Slidekicks scratchers
I also fried a starter motor, but that was my fault not Yamaha's (power supply for temp gauge)
No other problems
stopdropanroll
TY 4 Stroke Master
6656. Minor issues.
larrypolaris
Expert
3230 miles.
One subframe.
One belt.
Two sets of slides
Three sets of carbides(man do Pilot Skis eat carbides on marginal snow)
215 gal of gas
One oil change
A whole lot of fun
One subframe.
One belt.
Two sets of slides
Three sets of carbides(man do Pilot Skis eat carbides on marginal snow)
215 gal of gas
One oil change
A whole lot of fun
Similar threads
- Replies
- 7
- Views
- 1K
- Replies
- 2
- Views
- 586
-
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.