Search results

Anyone know of a thermostat I could get from a parts store? Maybe a small car or something? No Yamaha dealer close by and none of them stock it anyway.

I was dismayed to see my upper shock bushings are done on the front of my 19 xtx, has the QS3 shocks. 3000 miles. Is anyone aware of an upgrade for the bushings? Is this a common problem? A search here didnt show much. Thanks.

I dumped my Nytro upside down pretty hard being foolish. Anyway all is well except now the gas gauge only reads full when it is full down to to about 3/4, even when its empty. I'm thinking something bent inside tank. Anyone have this problem?

This happened about 6 weeks ago. I was keeping it quiet as I thought Yamaha may be interested in helping me out. Sadly, they wont return my emails. People need to know this. I was standing on Virus (what I named my sled), accelerating from a rolling speed of about 20 mph on a groomed trail...

Working on buddies Nytro and found this collar off the driver. One on the other driver is the same way. He is an easy rider so I dont think it will hurt anything but is there a way to get it back on without ripping out the axle? Has anyone seen this before?

Is there a way to press the bearing off the shaft to install loctite with out ruining the seal or bearing? My shaft was in about a millimeter and the bearing is moved in almost as much also. I pressed the bearing on the shaft further to see if it would move tighter and it did, but likely I need...

Holes for front shock shaft drilled in wrong spot, idler wheel mounts do not fit. They have not responded to my email asking what happens next, very dissapointed in this company.

They are discussing this in a motorcycle forum I frequent. I think it may work better on our sleds, if there is one that fits. https://www.fumotooildrainvalve.com/

This sucks. Was maybe going to be my last ride of the year. Now it definitely is. So I want to price this through Arctic Cat, there is a local one here. Is this the same as my 19 Sidewinder xtx LE ? Has anyone had any luck straightening rails ? The other side has just a slight tweak to it...

Black rod is hitting on the aluminum rod. All stock. Anyone else have this and should I be concerned? Its more than just a mark. Both are gouged a little but nothing bent yet, I noticed this when I went to loosen off my rear spring. Felt like it was riding too stiff.

Engine first occasionally had slight miss immediately after hitting the throttle hard. Eventually it would continually stumble and die intermittantly losing all electric. Finally it wont run, no power at all. No lights, nothing.This happened over 30 miles. My heated visor is connected directly...

Anyone else having the rear stock spring rub against their stock shock resi on factory settings? Slight rubbing on two coils. Pretty sure nothing is bent.

How loose or sloppy should they be? My offset is now 58.5 but I am still getting dust and think the performance should be better. A guy I know races Yamahas and he claims the 2019 rollers wear on the inside. My rollers seem loose.

I have complete stock 19 xtx. Belt dust gallore. I have learned if I dont drive much harder than 60 mph on hard pack I wont blow a belt. Should have bought a Bravo. So I took the shim out from behind the secondary to see what happens. Belt squealing at idle was what I got. Put it back in. This...

I have a black mark all around the top of my primary the width of the belt. I do mot have the top end I should have. Completely stock 2019 xtx le 141. I am thinking a stiffer spring or maybe heavier weights. Or both. I am no clutch guru. What do I need to fix this? about 1000 miles on it and one...

The left one is a Nytro flex pipe. The right one has a slightly narrower bolt pattern, less than a 1/4" and has the raised ring around the pipe on the flange. Other than this they are the same. I bought 3 of these used to fit my Nytro somewhere not sure if it was here or Ebay or what. I am...

Swiped this image off a post from Drantel. Anyone know the part number of this luggage? .

So, bought a new xtx le and went for first ride. Sweet :) But my gas cap is gone. I am assuming I didnt tighten it properly in my excitement to ride. Noticed this about 60 miles in. I taped a plastic baggy around, poked a little hole in it and made it the rest of the day without issue. Does...

I am considering changing my tunnel as it is tweaked a little and many loose rivets. I have an 09 xtx and found one from an 08 mtx. Is it a direct bolt (rivet) on exchange? I would rather keep looking for the same one than have to modify it to fit. I am not extending the tunnel or the skid. I...

Cut up the housing and ground down the light to make fit. Run the wire under the tunnel inside a water line from an ice maker and glued it all on with silicon. A couple pop rivets for added strength. Covered the hose with Gorilla tape. Now I will find some kind of tunnel bag.