Search results

I have a 06 Vector question. I took apart both fuel pumps to verify they were clean. I did not take any gaskets off. One at a time and reassemble. I screwed it back together but not super tight, like when I took it apart. The bottom fuel pump is leaking. Should I just tighten it up. I did not...

Im changing out the track on my 06 Yamaha Attak and want to change out the bearings since the sled has 9,900 miles on it. I see four bearing: Clutch, Chain Case and Drive Line. OEM only. Thanks in advance. Do I replace the oil seals and O rings too? #22 93306-20532-00 CLUTCH #2...

06 Attack Changed the stator and sensor replaced with Yamaha stock. Changed the oil. Now I got a 12 code? Need some help please. What can I check.

I have a 06 Vector that had a fried starter. I replaced it with a OEM Viper starter which is the same part number. I also replaced the starter relay with OEM. The sled did not want to start after I pressurized the gas tank. I removed air box and sprayed some starter fluid in the carbs. The...

Can you use 06 Apex copper donuts on a 06 Vector?

Broke the small nipple drain on the air box. Anyone have this issue and how did you fix it?

I want to install my Garmin Nuvi with a hard wire kit to my Attak. The kit has the regulator and inline GLASS fuse in line. What is the best and safest way to get the power. The regulator also has a red light that stays on ALL the time, not crazy about that. I read about a couple options...

I have 3 place R&R 7 ft wide enclosed trailer. I'm adding Caliber ski guides and radius guides. I need a layout plan for ramp and trsiler that works. Thanks

What is the size of the rivets used on the Apex Tunnel Traction brackets? Thanks

The snowmobile season ended awesome, thanks to Travis at Barn O Parts. Great guy to work with and he has a ton of Yamaha parts. So if you need a part check them out.

Is there a torque spec for the 10 mm bolt that hold in the flex pipe? I thought there was one. Sent from my SM-N920V using Tapatalk

How do you remove the coolant cross tube on a Attack/Apex? I lifted the back of sled, unhooked the hoses. It looks like that was put in the sled first. The tunnel protectors are over the tube, but I'm not sure if would slide out if they were loose. Suggestions.

I bought new gaskets for inside of the exhaust. They have a metal edge on one side. I'm thinking the metal edge goes out?

My 06 Attak exhaust is stuck. Tried to push with screw driver on the clamp . Hit the can with hammer on a piece of 2x4 centered. The pipe is so tight to pipes I can't get it off.. Suggestions. Thanks.

Can I remove just the back two bolts to drop the skid only? I need to fix the exhaust clamp. Thanks.

Needs some help here on my 06 Attak. Last year in Munising, my sled had a hard time starting. I just put in a new stock battery. It would start but had a hard time idling on 1 unless I held the throttle a little bit. Thanks for your help in advance.

I have a three place inline trailer with ski guides and on both doors. The main deck is bare wood. Im looking for options to protect the floor from studs at low cost. Im considering adding another layer of wood down on the entire floor. Thanks

Can you use Only one SS Y pipe and TT pipe on a 06 Attak?

I have read the stickie above. Anything I should I should do using the copper donuts instead of stock? Replacing right side Y pipe due to cracked flange. thanks

HI TY Members During the winter months Im on the snow snowmobiling or on TY Rides. All the other months, I play the drums in a band called The Split from Detroit, Michigan. My band is doing a Pledge Music campaign to raise money for a 7 song LIVE Video. When you pledge in return your get...