Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
We are no longer supporting TapaTalk as a mobile app for our sites. The TapaTalk App has many issues with speed on our server as well as security holes that leave us vulnerable to attacks and spammers.
After 19000 miles my nytro cooked the stator. Is there aa y way to remove the flywheel cover without pulling the engine out of my sled. I have the cover loose but iy won't come out.
My 08 rtx is blowing ignition fuses. I suspect I have a spot in my wiring harness worn bare. Is there any common suspect areas to look first. I have read about this issue on this forum. Thought I'd post this while I'm waiting for my buddy to comeand haul the sled and me home.
I have new drive sprockets for my 08 rtx nytro. Does somebody have dimensions for how far to press them on the shaft. I got them from Schmidt brothers and they forgot to send instructions.
I finally broke down and got a heated helmet shield. I have read threads on here before about where to wire it into the sled but can't seem to find them now. So where do I tie into a switched, fused power source on my 08 RTX?
I have an 08 RTX 121 sled. I have been running an Ulmer stage 1 clutch kit for the last 4 or 5 years. The cam arms are getting worn out so I will need to make a move soon. I am thinking of getting the rollers and spring that Schmidt Bros. use in there kit for the primary clutch because of the...
I have an 08 rtx, my service manual shows the 3 spring catch holes in the rear half numbered 1,2,and 3. There are no numbers at all on mine. How do I decide which hole is number 1?
I broke the dimmer button on on my 08 RTX. The button is available for newer nytros but not the 08's. Can I put the button from a newer sled in my 08 or do I have to get a whole new switch?
I just repacked the bearing on the speedometer side of my drive shaft. I noticed I can slide the shaft side to side an inch or so. Is this normal or is this telling me the bolt in the chain case end is broken or backed out?
A friend of mine has an 08 nytro that has been running fine, then lost fire on one cylinder. Swapping coils and plugs show that they are not the problem. Any ideas?
I just rebuilt my secondary clutch with bushings and ramp buttons. There are three holes in the secondary shieve. They are not numbered but are refered to in the manual as holes one, two, and three. How do I determin the correct numbering of these holes. The service manual seems to show the...
I keep getting a code 81 on my 08 nytro. The book says open or shorted hand warmer circut. My hand and thumb warmers work fine. If I shut the sled off for a minute the code goes away and maynot be back all day. I have a yamaheater on it and the newer handlebars with heated hooks. I have checked...
I have just under 8000 miles on my sled. I seem to be going through motor oil just lately. I don't see any puddles from leaks and I wondered if running washboard hard was putting it over into the intake. When I did a head gasket last year the cylinder walls looked good, you could still see...
I'm getting ready to put my sid back in with the new spring set up. What did you guys use for a starting point on the spring height ajustment and transition ajustment?
I installed a OFT handlebar relocator on my 08 RTX last night. It went togeather fine but I have a question about the lower pillow block. They tell you in the insructions to bend the studs on the subframe forward till the handlebars lay flat in the bearing. That's easy enough but then the block...
The holes on my lower A-arms are wallowed out a little bit. I saw in a post you had welded the nuts for the pivot bolts to the subframe. Are you using the factory locknuts and just locktiteing the bolts into them after the nylon lock stuff melts during welding or are you using diffrent nuts...
I was looking at clutch pullers on ebay. They list a puller for the 06 to 09 Nytro's. What changed after 09 with clutches and or cranks to need a diffrent puller? I have an 08 RTX so this puller should be fine. I was just wondering if there is any changes?
So what is the deal on wet left foot syndrome. Wore my leather shoes today and I was able to wringe the water out of my sock when I got home. I have heard about this, but today was the first time it got me. Is there airflow off the belt that is throwing moisture? Any inexpensive cures or is...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.