Search results

Been a long while since I’ve posted on here. Was about to do my oil change today and I noticed there was some coolant on the frame. After warming it up I can see a drop of coolant on the lowest screw that hold the two halves of the pump together. I’m guessing the pump needs replacement...

My idle has been a little low this year and today when it was really hot the idle dropped low, 1200ish rpm, code 30 came up and the motor stopped. It restarted and seemed fine but it happened two or three time thought out the day. Now I’ve noticed that it’s not unusual for my sled to see a...

My GT has the sliding block style sway bar. Has anyone ever seen a quick disconnect setup for this style on Yamaha or other brand?

I was wondering if anyone has see or used this trunk bag: http://www.gearscanada.com/snowmobile/tail-bags/rage-4-tail-bag.html? Or even heard of the company. I like the idea of the bungees on the outside and it looks like you could strap a shovel to it. It seems somewhat universal and larger...

Now that I have a 136" I finally have space to mount a shovel on the the tunnel. Does anyone have a pictures of what they've done? Or any bags they've tunnel mounted? Also before anyone mentions a backpack, I hate wearing them and I'm on the prairies so there is no avalanche safety risk of...

I warmed up my sled today, shut it off to fill it and then went inside for an hour. When I came back the fuel pump wasn't priming. After trying it a couple of time it eventually started. I'm guessing the relay is failing. It's the original from 2007. My understanding is there is a update solid...

Last night while working on my 136 conversion I noticed the front arm in the rear suspension has started to crack at the weld but hasn't broken yet. I know there was a lot of early failures on the 2007 but this one is all original parts with about 10,000 km on them. My brother, who is a...

My 136" Freeride kit from Tracks USA should be here this week but I was wondering if anyone has a Ulmer kit and would recommend any changes in clutching with the longer track? I'm already running a 18t gear.

I just want to post a word of caution with the anti-bottoming kit. I installed one last year and the when checking my skid this year found both of the lower torsion spring mounts have broken on the top edge, the thing that retains the spring. From what I can figure, when the sled is going to...

I've been thinking about a track change but I'm wondering about my factory cover still fitting. If I did a 128 track swap I'm guessing I could get away with out stretching the tunnel and cover would fit. If I do a 136 swap do I have to extend the tunnel and is there anyway to get the cover to...

I was changing the oil today and found a rather bad crack on the aluminum side frame panel right below the chain case cover. The chaincase don't appear to be leaking but where the aluminum cracked it is pushed closer to the track. Has anyone ever taken the side panel off? I'm going to...

Hi, I just got my Oillite kit from the Yamaha and I was wondering do you still pack the tubes with grease when you assemble them? Thanks.

I found a set of MTX skis but they are missing the bolt and spacers. Before I buy them do has anyone made their own spacers or found a cheap source for them?

I've been reading though the posts on here about gearing and I've got a question. I've got a 07 GT with the stock 1 inch Hacksaw on it along with an Ultra Q exhaust and Ulmer Clutch kit. It has the stock 20 tooth gear in it right now. I'm thinking about drop to a 19 tooth gear to give...

I was thumbing though the manual for my dad's 07 Vector GT the other day and I noticed that for the mountain sleds they talk about a "Carburetor Coolant Shut-off Lever". We quite often ride in the spring when the temps are above 0°C and the manual suggest you shut the carb heaters off at...

I posted something similar in Ulmer section earlier this week but haven't revived a response so I was hoping some one here could offer some advice. I just installed a Ulmer clutch kit on the weekend and here is my issue. When I pin the throttle the rpm would go to 11000 then back down to...

Does anyone have a pdf of the shop manual for a 2007 RS Vector GT? If so could I get a copy? Thanks.

Has anyone with an 07 GT had the link brake? It seems like all the ones I read about are FX's or base ones. I'm asking because I have an 07 GT and I want to know if I should be pressing my dealer to upgrade to 08 parts before it fails or my warranty runs out.

Hello, I'm new here and I just bought a 2007 Phazer GT. I've been wondering if anyone has looked at installing a command start on it. Also would that void the warranty? Thanks, Andrew